耐特艾嘉

自从买了J.A.F刷机盒子后, 心里总是痒痒的. 于是今天又那里朋友的nokia 7370 来刷了一把, 把手机系统软件从3.51 升级到了4.05, 还把手机的内置代码改成了APAC-R CTV CHINA, Stroke, AMBER^0531132^V 04.05^005 爽死了. 以后谁买了nokia的机子都可以叫我来升级软件和刷中文解锁.

下面贴点刷机的经过和log

I tried many times, finally I found some hints. but still could not flash my 7370 via usb mode...

I directly connected the usb to pc and chose the default mode

BOX OK
J.A.F. by ODEON - ver 1.95 beta1, FW: 01.A2
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
Changing JAF to BB5 mode...Done!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\products\RM-70\rm70__04.05.mcusw
PPM Flash file: C:\Program Files\Nokia\Phoenix\products\RM-70\rm70__04.05.ppm_p
CNT Flash file: C:\Program Files\Nokia\Phoenix\products\RM-70\rm70__04.05.image_p_warm
Searching for phone...Init usb communication...
Found
Reading battery value...0 mV
Battery level is too low...Please make full charge and try again!
Searching for phone...Init usb communication...
Found
Reading battery value...0 mV
Battery level is too low...Please make full charge and try again!

after saw above log, I unpluged the usb, and pluged in, then I clicked flash quickly, it had different log as below:

Searching for phone...Init usb communication...
Found
Reading battery value...4061 mV
Setting local mode...
Init usb flashing...
Reading mcuid... Reading flashid... CMT: 22FE00EC, APE: 00000000
Verifing ADL communication... Status byte 2
ADL->Loader: Update Application Loader -> Single Chip
Loader len: 156992, CHK: 0xEB06
ADL -> Sending loader...
.................................................. ..................Fail to send UPD loader...

but it did not last long... said " fail to send UPD loader" then I clicked flash again, got the following log:

Searching for phone...Init usb communication...
Found
Reading battery value...0 mV
Battery level is too low...Please make full charge and try again!
Reading battery value...0 mV
Battery level is too low...Please make full charge and try again!

finally I tried to make my phone into dead phone. then I powered off when I began to flash, finally my phone was dead, and I ticked the dead usb and flashed it... I followed the instruction and it was flashing!!!!!!!!!!!!!!

Searching for phone...Init usb communication...
Found
Reading battery value...4039 mV
Setting local mode...
Init usb flashing...
Reading mcuid... Reading flashid... CMT: 22FE00EC, APE: 00000000
Verifing ADL communication... Status byte 2
ADL->Loader: Update Application Loader -> Single Chip
Loader len: 156992, CHK: 0xEB06
ADL -> Sending loader...
.................................................. ................................
Waiting for the phone to boot...
Phone is in flash mode...
Phone failed to boot in flash mode...
Searching for phone...Init usb communication...
Found
Reading battery value...0 mV
Battery level is too low...Please make full charge and try again!
PRESS POWER ON THE PHONE NOW!!!
Searching for phone...Init usb communication...
Found
Starting DEAD USB phone flashing...
Error reading phone init data...
Searching for phone...Init usb communication...
Found
Reading battery value...0 mV
Battery level is too low...Please make full charge and try again!
Searching for phone...Init usb communication...
Found
Reading battery value...4036 mV
Setting local mode...
Init usb flashing...
Reading mcuid... Reading flashid... CMT: 22FE00EC, APE: 00000000
Verifing ADL communication... Status byte 2
ADL->Loader: Update Application Loader -> Single Chip
Loader len: 156992, CHK: 0xEB06
ADL -> Sending loader...
.................................................. ....Fail to send UPD loader...
PRESS POWER ON THE PHONE NOW!!!
Searching for phone...Init usb communication...
Found
Starting DEAD USB phone flashing...
Using 06.02.002
Elf2flash 02.31.000 RAW loader...
Patching RAW boot step1...
Patching RAW boot step3...
Sending RAW Loader...
...................Loader Sent!
Stage 2 starting.......................................... Loader Sent!
Stage 3 starting..........Phone prepared OK!
Waiting for the phone to boot...
Phone is in flash mode...
CMT blocks: 1261, APE blocks: 0
Erasing cmt...
Erasing cmt zone 00000000 - 000FFFFF ...
Erasing cmt zone 00120000 - 0013FFFF ...
Erasing cmt zone 00140000 - 0017FFFF ...
Erasing cmt zone 00180000 - 00BFFFFF ...
Erasing cmt zone 01100000 - 01FDFFFF ...
Erasing cmt zone 00C00000 - 010FFFFF ...
Writing cmt...
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->PAPUB_CERTIFICATE_DATA_BB5 block detected
cmt->PAPUB_CERTIFICATE_DATA_BB5 block detected, sending...
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
cmt->Rootkey hash detected
cmt->Matching CERTIFICATE_DATA_BB5 block detected
Rebooting...
Pooling phone...
MCUSW: V 04.05
16-03-06
RM-70
(c) Nokia.
APESW: (null)
VariantSW: (null)
Prodcode: 0531132
DCT4/BB5 counter: 2
Done!